模切压痕机19个操作规程 19 operating procedures of die cutting indentation machine

1、使用模切压痕机的车间设备布置应合理、道路地面平坦、通道畅通。

　　2、模切压痕机的安装方向应有利于安.全操作，以操作者面向墙壁为宜，其与周围建筑及设施的*小净距离不的少于0.8m。

　　3、安装地点应能满足垂直起吊及维修作业的场所条件。

　　4、模切压痕机应设备完好，技术资料齐全，随机专用工具齐全、完好。

　　5、模切压痕机的电动机、电气控制箱等金属外壳，必.须有良好的接零或接地保护。

　　6、外露于模切压痕机的导线必.须用保护套管，不同电压的导线要采用各自的套管。

　　7、使用单位对模切压痕机建立安.全技术档案，记录安.全生产情况。

　　8、对模切压痕机的操作工人应进行安.全教育和专.业技术培训。

　　9、模切压痕机操作工人必.须身体健康。

　　10、严禁操作工人连班，如需单机加点时不应少于2人。

　　11、用于检查和修理版面的照度不低于300lx，操作处的照度不低于100lx。

　　12、模切压痕机应尽量采用自然光源，自然光源不足时应设置电力的一般照明。

　　13、电力的一般照明不得依附于机身。

　　14、电力局部照明采用安.全电压。局部照明的照明器应有不透明材料或漫射材料制成的反射罩。照明器的位置高于操作者水平视线时，其保护角度不应小于30°；低于操作者水平视线时其保护角度不应小于10°。

　　15、操作工人必.须穿紧袖工作服，并使用专用胶指套。

　　16、模切压痕机的操作高度应以操作工人站立工作时不踮脚、不弯腰为宜。

　　17、采用手柄式制动开关，其手柄端点的动作距离不大于30mm。

　　18、气动离合器与制动离合器必.须同步动作。

　　19、开车时应先空载试用离合器，离合器工作应平稳。 

1. The layout of workshop equipment using die-cutting indentation machine should be reasonable, the road ground should be flat, and the channel should be unblocked.

2. The installation direction of the die-cutting indentation machine should be conducive to safe operation, and the operator should face the wall. The minimum clear distance between the machine and the surrounding buildings and facilities should not be less than 0.8m.

3. The installation site shall meet the site conditions for vertical lifting and maintenance.

4. Die cutting indentation machine should be in good condition with complete technical data and special tools.

5. Die cutting indentation machine motor, electrical control box and other metal shell, must have a good neutral or grounding protection.

6. Exposed in the die-cutting indentation machine wire must use protective sleeve, different voltage wire to use their own sleeve.

7. The user shall establish safety technical files for the die-cutting indentation machine and record the safety production situation.

8. Die cutting indentation machine operators should be safety education and professional and technical training.

9. Die cutting indentation machine operators must be healthy.

10. It is strictly forbidden to operate workers in continuous shifts, and there should be no less than 2 workers when a single machine is needed to add points.

11. The illumination used for checking and repairing the layout shall not be less than 300lx, and the illumination used for operation shall not be less than 100lx.

12. Die cutting indentation machine should try to use natural light, natural light shortage should be set up when the general lighting power.

13. General lighting of electricity shall not be attached to the fuselage.

14. Safe voltage is used for local lighting. The illuminator for local lighting shall have a reflector made of opaque or diffuse materials. When the position of the illuminator is higher than the operator's horizontal line of sight, the protection angle should not be less than 30 degrees; when it is lower than the operator's horizontal line of sight, the protection angle should not be less than 10 degrees.

15. Operators must wear tight sleeve work clothes and use special rubber finger sleeves.

16. The operating height of the die-cutting indentation machine should be such that the operator does not stand on tiptoe or bend when working.

17. The handle type brake switch is adopted, and the action distance of the end point of the handle is not more than 30mm.

18. The pneumatic clutch and the brake clutch must act synchronously.

19. Try out the clutch with no load before driving, and the clutch should work smoothly.